Dyson DC25 Not Spinning? Answered!

Is the brush on your Dyson DC25 not spinning? Your vacuum brush may stop rotating for a variety of reasons. We’ve done our homework and know just how to diagnose and repair this Dyson vacuum issue.

This vacuum problem has a few easy solutions. If a blockage causes it, you’ll have to clear it out manually. You may have to cut the brush to remove the debris. Another typical issue is overheating. Before attempting to vacuum again, empty the canister and clean the filter. Your brush might also stop spinning for a variety of reasons. Clogging, on the other hand, is the most prevalent. Continue reading to learn how to clear a blockage and other brush roller troubles.

How To Fix: Dyson DC25 Not Spinning

The Brush Has Become Clogged

Consistent usage of your Dyson DC25 without regular brush bar cleaning may result in this, which is to be anticipated since the machine constantly comes into contact with hair that becomes entangled with the brush bar. Fortunately, there is a workaround.

Step 1: Turn off the vacuum and set it naked on the ground. This is to make the brush bar more accessible.

Step 2: Separate the brush bar assembly from the sole plate. It varies per model, but you will need to turn various screws.

Step 3: Remove threads and fibers with your scissors. To prevent interfering with the bristles, proceed with caution.

Step 4: Separate the brush bar from the brush and pull it out to provide access to the nooks and crannies. You may clean the threads from one end to the other.

Step 5: Reassemble the brush bar and cleaning head into one piece using the same process you used to disengage them.

2. Unclean Electrical Connectors

The brush bar is housed and spun by the Dyson cleaning head, an electrical component of the vacuum. It means it receives its power from the battery near the engine, housed within the handle you use to operate it.

See also  Dyson DC24 Not Picking Up? Fixed!

The battery powers the cleaning head through a few electrical hookups strewn throughout the vacuum. These electrical connections may be found everywhere the vacuum’s components connect, including the cleaning head, the wand, and even the handle and the motor.

Dyson vacuum cleaners leave a trail of dust all over the house. In the long term, dust will build around the sections with electrical contacts. Electrical connections coated in dust cannot provide electricity as far as feasible toward the cleaning head, preventing the brush bar from spinning. If that’s the case, you’ll notice that the brush bar spins irregularly or not at all.

To resolve this problem, disassemble the vacuum and separate the cleaning head, which houses the brush bar, the wand, the dust-collecting tub, and the motor from the handle, which houses the battery. Then, clean all the electrical contacts using a high-quality bristle brush or a dry towel to eliminate any dust or obstructions.

Reassemble the vacuum after you’re finished. The cleaning head should have no problems receiving electricity. The brush bar must be spun.

3. Loose or Broken Belt

A loose or damaged belt is another factor that might cause your Dyson to stop spinning. The brush bar is inextricably linked to the belt, and it is the belt that facilitates movement; thus, if the belt fails, the brush bar will not spin. Let’s look at some more practical options for dealing with this scenario.

Step 1: Turn off the machine and lay down. Then look at the brush bar; if two of them are separated by a drive mechanism in the center of the assembly and are linked by a direct drive mechanism, you won’t need to change the belt. However, if one bar spans across the assembly, you may be certain that a belt on one side controls it.

Step 2: There are two ways to proceed with the next step depending on the model: disengage the brush bar from the belt with a lifting tool if you can easily see the belt, or remove the cover from the side of the structure to gain access to the point where the bar and the belt are connected if you can’t.

Step 3: After crossing the bridge, replace the belt with the one advised for your model. It is preferable to utilize the appropriate belt for your machine to keep things simple for the machine in the future.

See also  What to Do With Old Dyson Vacuum? 5 Awesome Things!

4. Blocked Wand Or Bin Inlet

From the brush bar to the vacuum bin, dirt, dust, and debris must pass. The engine will provide enough suction to suck all the dirt to the vacuum bin as the brush bar pushes the dirt on the ground. Before entering the real container, the dirt flows through the wand and the bin inlet.

There is always the possibility of dirt accumulation wherever it moves. Dirt, dust, and other nastiness will most likely form in the wand or bin of your Dyson vacuum in this case.

The pile accumulates, and the vacuum gradually loses its suction force. When the suction force of the brush bar is reduced, the brush bar’s capacity to spin is also reduced.

You’ll need to separate the wand from the cleaning head and the bin entrance to get around this problem. After that, clear out any dust specks you find, giving special attention to both ends of the one that connects the cleaning head to the bin intake.

5. Unclean or Dirty Brush Bar and Cleaning Head

A rotating bar with bristles makes up the brush bar. The cleaning head spins quickly to remove dirt, dust, and debris from the ground. From there, the vacuum’s powerful suction will easily and effectively collect all the dirt. The brush bar and cleaning head are connected to the wand and the rest of the vacuum as a single piece.

The brush bar on the Dyson vacuum easily picks up loose debris. Nonetheless, the brush comes into contact with larger objects such as human and pet hair, which are difficult for the vacuum to suck up past the cleaning head.

Hair will become tangled in the brush bar’s bristles and other moving parts. Each time you use the vacuum, the tangled mess will get bigger until the brush bar stops spinning.

To resolve this problem, clear the entanglement on your brush bar, and begin by opening the cleaner head, which helps keep the brush bar intact. After that, slide your brush bar out and clean any stuck hair, dirt, or fur.

If there are any thicker entanglements, you can cut them with a pair of scissors. However, you must be extremely cautious to avoid damaging the bristles. Ensure the cleaning head’s attachments are removed, as well as all dust, hair, and debris.

See also  Dyson Airwrap Not Turning On? Try This!

How To Fix An Overheating Vacuum

The brush will not spin if your Dyson vacuum is overheated. The vacuum will automatically switch off the roller if the filters get clogged. If the debris tank is also full, you’ll know it’s overheated.

You’ll need to clear your debris bin first. Clean the dirt from the central cyclone once the bin is empty. You’ll need to clean or replace your filters to fix the problem.

A pre-filter and a post-filter are included with Dyson DC25 vacuum. These filters may be cleaned by running them under cold water. Allow them to dry fully before reinstalling them after the water has run clean. If it has been more than a year since you last updated the filters, you may need to replace them.

How To Fix Vacuum Seal

The Dyson may fail to function if you have previously dismantled the vacuum and did not reassemble everything properly. This also applies to the Dyson roller not rotating.

The solution is straightforward. Remove the vacuum from the outlet and place it on the ground. Make sure that the seal surrounding the cleaning head is intact. Push the cleaning head up against the vacuum’s main body if it’s loose.

The cleaning head is finally in position when you hear a click. Reconnect the vacuum and test it to see whether the “Dyson vacuum not spinning” issue has been resolved.

How Do You Reset A Dyson Ball Vacuum?

Essentially, resetting your vacuum involves disconnecting and reinstalling the power supply. To reset the brush bar, double-click the vacuum’s brush control button.

This brush resetting procedure is compatible with all Dyson vacuum cleaners. Another easy solution is disconnecting your vacuum, letting it rest for a few minutes, and then reconnecting it.

Dyson Turbine Head Not Spinning

Dyson offers a wide range of vacuum cleaner models. The way they’re built differs, but the troubleshooting advice is the same. The structure is typically the most significant distinction between Dyson models. Regarding troubleshooting, they all have the same components and filters; the only variation is how to disassemble the vacuum.

Conclusion On Dyson Dc25 Not Spinning

There are just a few possible causes for your Dyson vacuum to cease spinning. First, inspect your vacuum head for debris and, if necessary, disassemble it. Even if debris is tucked away in the frame, it might create issues.

After that, inspect and clean the debris bin and filters. Finally, check the power cord and vacuum settings if your vacuum still won’t start.