If you’re struggling with your Eufy Robovac Not Connecting To Wifi, the first step is to check the wifi indicator light on the vacuum.

If your device is quickly flashing blue lights, it’s possible that you typed in the wifi password erroneously or that it hasn’t been disconnected from a prior network; this is typical with second-hand gadgets. You’ll need to reboot your wifi connection to repair this. Hold the power button for 10-15 seconds until it beeps. The status light will now progressively flicker blue, indicating that you are ready to connect.

Reasons Eufy Robovac Not Connecting To Wifi

Table of Contents

Move The Router Closer To Your Eufy Robovac And Your Phone

The robot’s wireless wifi light indicates that your router is too far away from your Eufy Robovac and your phone. The robot cannot connect to a wifi network due to this. If this is the case, try bringing your robot and phone closer to the router and reconnecting the robot. Whether this does not solve the problem, check to determine if your router is operational.

Place your home router as high as feasible in the center of the room. This should, in most circumstances, be sufficient to enhance signal strength throughout your home. If your router’s wifi connection is still poor even when it’s near your robot and phone, consider resetting it. If the problem persists, your router may need to be upgraded.

The TP-Link wifi 6 Router AX1800 is a good option. With wifi rates up to 1.8 Gbps and Next-Gen 1.8 Gbps capabilities, you can experience faster and more consistent streaming, gaming, downloading, and more (1200 Mbps on the 5 GHz band and 574 Mbps on the 2.4 GHz band).

Disconnect A Few Other Devices From The Wifi Network

You’ll need extra bandwidth to keep up if you have numerous devices and several family members using them simultaneously. Any household with more than 10 devices connected to the internet at the same time is likely to have bandwidth challenges.

Streaming, gaming, and other high-capacity activities need a particular bandwidth speed to enjoy the best experience possible with minimal buffering or latency. If you’re having problems connecting your Eufy Robovac, go to your router’s settings and go through all the devices connected to your Wi-Fi network. Disconnect any that aren’t in use.

The more bandwidth you have on your Wi-Fi network, the more bandwidth space you have for your Eufy Robovac. There is less competition from other devices for a good Wi-Fi connection.

Also, while connecting the Eufy Robovac to the router, the VPN must be temporarily stopped since you cannot connect your Eufy Robovac or the EufyLife app to a virtual private network firewall must be removed as well.

Examine The Battery And Settings Of The Eufy Robovac

The Eufy Robovac comes with a rechargeable battery that lasts between 100 and 180 minutes, depending on the model, and it must be completely charged before usage. As a result, if the robot’s battery is low, it may lose its internet connection.

Check to see whether your Eufy Robovac is in Reduced Power Standby mode. While this mode is engaged, the Eufy Robovac’s Wifi will be deactivated.

When the Eufy Robovac is being charged, press and hold the POWER and CHARGE buttons simultaneously for 20 seconds until the Power Status Lights turn off to enter Reduced Power Standby mode. To leave Reduced Power Standby mode, press the POWER button.

Make Sure Your Router’s Name And Password Are Accurate

If you have a lot of wifi extenders in your house, you can type the name and password incorrectly. Check that the wifi network name and password you used are accurate. Please try again if it is wrong.

If you’re using a network extender, make sure the network name (SSID) and password on the extender are the same as your main network. Otherwise, when it goes from one range to another, your Eufy Robovac may lose its connection.

Update Firmware

When Eufy provides new updates to enhance the performance of their goods and resolves security flaws, connection difficulties may arise if the robot is not updated. Here’s how to use the EufyHome app to update your Eufy RoboVac:

To ensure the RoboVac has adequate power, place it on the charging base.
Make sure your home’s Wifi is reliable.
Select the Robovac option on the EufyHome app.
The “Firmware Update” button may be found by tapping the three dots in the upper right corner.
To upgrade the firmware, click it.

Examine The Robot’s Battery

The Eufy RoboVac comes with a rechargeable battery that may last anywhere from 100 to 180 minutes, depending on the model, and it must be completely charged before usage. If the battery is low, the gadget may lose its internet connection. Check whether your RoboVac is in Reduced Power Standby mode, a feature featured in many RoboVacs that allows you to charge faster but disables Wifi.

Power Cycle Your Modem And Router

If your internet plan isn’t dead yet and your battery is OK, but your robot is still down, you may try power cycling the router and modem. aTo power cycle your modem and router, follow these steps:

If you have a battery-powered modem or router, turn it off and unhook it from the outlet, or remove and replace the battery.
Allow 60 seconds to pass.
After plugging them in, please turn on the modem and router, and wait for them to fully start up until the front panel connection lights on the modem display a stable connection.

Reset The Eufy Robovac

If none of the preceding suggestions work, factory reset your RoboVac, since this is an effective remedy for most issues. Here’s how to factory reset your RoboVac:

To reset the wifi connection, press and hold the ON/OFF button on Robovac for 10 seconds. When the wifi connection is reset, you will hear a beep, and the wifi status indicator will progressively glow blue.

Make Sure Your Phone Settings Are Correct

Last but not least, before connecting your phone to your Eufy Robovac, double-check your phone settings. To make sure it’s set up properly, follow these steps:

In your phone’s settings, enable GPS and provide your EufyHome app location access. Please enable the “exact location” option if one exists.

Before you begin connecting, enable Airplane mode and switch on wifi only. Cellular and mobile data should be turned off.

For roughly 10 seconds, press and hold the START button on the vacuum’s top until you hear a beep. Check to see whether you can hear the buzzer. Please press and hold both of the top buttons on the robot until the “reset wifi” audio alert is heard. Check to see whether you can hear the voice alert.

A steady flashing light indicates that your Eufy RoboVac is “ready to connect,” while a rapid flashing light indicates it is “connected.” The Eufy Robovac is only “connected” if the light is solid blue.

Does Eufy Vacuum Work Without Wifi?

You don’t need wifi to use your Eufy if it has a remote control. You may use the remote control to program your vacuum and start/stop it. Because some of the newer models don’t come with a remote, you’ll have to set them up using the Eufy Home app on your smartphone.

A wifi connection is required for this operation, but it does not have to be a real internet connection. Even if you lose your wifi connection after setting up the vacuum, it will continue to work. You’ll need a wifi connection to make any settings changes. If you want to manage your vacuum when you’re not at home, ensure it’s linked to the wifi network and has an active internet connection.

How Can I Connect Robovac To My Wifi Network?

To use a wifi connection to set up your Eufy Robovac, follow these steps:

For Android or iPhone, download the Eufy Home app.
If you don’t already have an account, follow the on-screen steps to create one.
Once you’ve signed in, go to ‘robot vacuum and choose your model from the drop-down menu.
Allow the vacuum to connect by entering your wifi username and password.
If your status light is slowly flashing, go to the next page and click ‘Confirm.
When a prompt appears on the screen, hit ‘Go to wifi Settings.’
Choose your Eufy Robovac from the drop-down menu.
The vacuum is now linked, and the next step is to name it.

Can You Use A Mobile Hotspot To Set Up A Eufy Vacuum?

Yes, you can use a mobile hotspot to set up a Eufy vacuum, but you’ll need two distinct phones to do it. The first phone will provide the hotspot, and the second phone should be linked to it. Then, on the second phone, download the Eufy Home app and use it to set up the vacuum. Keep in mind that after the mobile hotspot is switched off, you won’t be able to change the vacuum settings.

Conclusion On Eufy Robovac Not Connecting To Wifi

So, if your Eufy RoboVac loses its Wifi connection, you may use this post as a guide, and if you have any further questions, you can contact Eufy customer service through live chat on their website or by calling them directly from your phone.