Are you having issues with your Miele brush not spinning? A spinning brush that fits into the vacuum’s head is a common feature of contemporary Miele vacuums. This brush’s function is to sweep away dirt and debris from the surface it is working on. Your vacuum cleaner’s functionality will most likely be significantly diminished if the brush stops rotating.
It’s typically quite evident if you have a defective switch or a wrong wire reel when a Miele brush suddenly stops working. The cord reel has malfunctioned in roughly 60% of the Miele repairs I perform for this issue.
The belt may be faulty, or if it has a clutch assembly, the clutch assembly has failed, depending on the make and model.
Why Is Miele Vacuum Brush Not Spinning?
There could be several causes for why the Miele vacuum brush stopped spinning. The meeting itself, one of the belts that drive it, or both could be broken.
1 . Wiring Problems Or A Broken Brush Motor
Your vacuum cleaner’s electric motor may eventually cease functioning if used frequently. Vacuum suction is powered by one of the vacuum cleaners’ two internal electric motors, while the other motor mainly drives the brush.
- The vacuum’s suction will continue to function normally even if the brush motor is entirely worn down, but the brush will not spin. It’s usually time to examine the engine if you’ve ruled out obvious problems like hair accumulation, a broken or disconnected drive belt, or some other visible issue.
If you’ve worked with electronics before, you might want to check to see if the brush motor is still functional by using a multimeter. The engine will need to be replaced if it displays no continuity.
- If your vacuum has a wire harness, you should also inspect it. Look at the wires’ contact points and notice whether it appears that any of them are cracked or melted.
- You will need to repair any cables in your vacuum cleaner that have visible evidence of damage.
If working on your vacuum’s motor seems intimidating, don’t hesitate to call a certified repair technician. This appliance repair is much more complicated than replacing your vacuum cleaner’s brush.
2. Bristly Brush
As we’ve already mentioned, the brush on your vacuum can become inoperable if the bristles become worn out over time from regular use. The brush will still be able to spin in this situation, but it will perform much worse than it was intended to.
It’s also possible for the brush to completely break, though this doesn’t happen as frequently. If the brush is old, the plastic it’s made of may have aged somewhat, which is not what you want in part intended to rotate at reasonably high speed.
Fortunately, replacing a worn-out brush with a new one is relatively simple.
- You should be able to slide or pop the old brush out after removing all the covers covering it and separating it from the drive belt.
- You should be ready after reconnecting the drive belt and pushing in the new brush.
Once more, it would be best if you were careful to purchase a replacement brush appropriate for the vacuum cleaner model you own.
3. Overheating
The electric motor in your vacuum overheats as it ages and begins to wear out because it has to work harder to generate the same amount of power. This may also be brought on by an overstuffed filter bag or vacuum canister, a hose obstruction impeding airflow, or even a worn-out drive belt.
Many vacuum cleaners are equipped with thermal cutoff devices that, when they notice that the motor is getting too hot, automatically cut off the vacuum cleaner’s power. There’s a good chance that overheating is the root of your problem if your vacuum cleaner usually starts but keeps shutting off after a few minutes.
- Unplug the vacuum from the wall and let it cool before opening it to deal with an overheating vacuum.
- Open it up, check the vacuum line and canister/filter bag for obstructions, and if you find any, empty them.
- Additionally, look to see if the drive belt has detached from the brush. The motor has much less resistance when the drive belt separates from the meeting, which allows it to turn on too quickly and overheat.
Allow the vacuum to sit for an additional half-hour or so to ensure that it has completely cooled down after removing any obstructions you may have discovered or replacing the drive belt. Next, try turning it back on to see how it operates.
If it functions regularly, you’ve fixed the issue; if it keeps turning off by itself, you should probably have your vacuum repaired.
4. Brush Is Obstructed
First and foremost, always disconnect your vacuum cleaner before performing any maintenance. It’s crucial to ensure the vacuum has no power before performing any repairs because you may need to handle any of the electrical components. You wouldn’t want to start your vacuum while repairing the brush unintentionally.
The brush on most vacuum cleaners is partially covered by an access plate, which helps maintain it in place. To properly access the bush, you might need to remove this plate, which typically calls for a screwdriver.
- Once you’ve removed the cover, note the state of the brush and the other visible parts. The most likely source of the issue is anything that appears broken.
- If not, likely, the brush isn’t spinning because it’s clogged with hair, dirt, and other debris.
- Likely, the brush is completely covered in hair and other debris. If so, simply attempting to pull it out won’t probably be very successful.
Instead, you should take the brush out of the vacuum head and cut the hair from the brush using a pair of scissors. Be careful not to miss any of the brush’s bristles when you do this.
5. Worn-Out Spindles Or Bearings
The brush can freely spin inside the vacuum head thanks to bearings or spindles on each end of the brush. These bearings/spindles may become ineffective and wear out over time. When this occurs, the brush will experience much more excellent resistance when attempting to turn.
Give the brush a spin inside the vacuum head with the drive belt off to check the health of your bearings and spindles.
The bearings or spindles are probably not the problem if the brush rolls easily.
If the brush is difficult to roll or seems to be out of alignment, there may be a problem with the bearings or spindles.
Sadly, it is not possible to detach the bearings and spindles from the brush and replace them. You will need to buy a new brush if your bearings or spindles break.
Disassembly and cleaning of the Miele Turbo Mini TurboBrush
Step 1: Overview
Digging out the hair/fibers using a medium-sized safety pin, trimming the brush’s hair with scissors, and removing the black plastic end caps with a flat-head screwdriver. For reassembly, you might require a tiny hammer.
No screws are present. Plastic pressure holds most components together. To avoid purchasing a new unit, take care not to break any plastic clips or parts.
Always spend a few minutes trimming hair or fiber off the brush after each usage to avoid disassembling this item frequently.
Depending on how much hair is lodged in the unit, disassembly and cleaning should take 30-45 minutes.
Step 2: Opening The Unit
Open the device by following the directions in the handbook. The rotating cuff is raised once you align the arrows, depress the small plastic button, and do so. This should enable the unit’s upper half to pivot upward.
Step 3: Delete The Fin Assembly
The component that causes the unit to rotate is now removed. The fins push the belt that rotates and moves the brush by the vacuum’s suction. Gently go to the little black plastic clips on either side of the Fin assembly to remove it. Because there is no way to fix the pins if you break them, use gentle pressure when doing this
Step 4: Remove End Cap
This is undoubtedly the trickiest and least intuitive portion of the disassembly. The end caps keep the entire device together, which only need to be popped in. Use a small flat-headed screwdriver to gently pry them off after pulling them by hand and turning them as much as you can. It will require some effort and pressure.
The center is where the caps are fastened (see the middle of the caps in the photo). When prying, you should concentrate on the pressure here. Plastic clips should be avoided, but you can force them off by pressing firmly.
Conclusion On Miele Brush Not Spinning
You might need to take your vacuum to a professional if this doesn’t resolve the issue and you can’t see any obvious physical signs of a problem.
However, there may come a time when you cannot resolve the issue on your own. Doing so will spare you from taking your vacuum cleaner elsewhere and will probably save you money on repairs.
A few typical issues develop with vacuums, and cleaning or fixing a damaged brush roll is a reasonably straightforward task. These issues are typically easy to spot, and solutions are frequently used.