Roomba Extractors Not Spinning? How To Fix

Are you perplexed and upset because your Roomba extractors not spinning freely? Many Roomba users face this problem, especially if their robot vacuums have logged many miles and are somewhat old. Before you can figure out what to do, you need to know why this is happening.

The most common reason for Roomba extractors not spinning is that the gears inside the brush gearbox have become too old and worn down. The gears might also become caught due to hair and dirt. The simplest solution is to purchase a new brush assembly.

Furthermore, the extractor’s motor may become too feeble after several years of use. In this post, we’ll go over the various reasons why the extractors on your Roomba aren’t spinning, as well as the measures you may take to fix the problem.  

Why are my Roomba extractors not spinning?

If your Roomba extractors are not spinning, please examine your device and respond to the following questions:

  • Have you plugged it in and charged it?
  • Have you verified the robot cleaner’s battery status?
  • Is there anything in the way of your Roomba’s extractors spinning because it can’t see it?

You must carefully check the extractors. If it stops spinning, it could be because the battery is dead or because it got caught on something. If it’s not due to the above causes, keep reading to learn how to resolve this and other Roomba extractors-related issues. There’s no need to be concerned because this issue will arise at some point if you buy a robot vacuum cleaner.

See also  Roomba Not Turning On - Solved!

What’s The Deal With A Roomba Extractors That Won’t Spin?

Roomba extractors that are not rotating properly could be caused by one of three things. In our experience with Roombas, the most obvious explanation is hair and dust buildup underneath the extractors, especially if it isn’t cleaned frequently. Here’s a more detailed explanation of each possible cause:

The Extractors Module Has Become Stuck

The most common cause of Roomba extractors not spinning is that it is clogged with hair or other contaminants. You’ll be shocked at how much dust and debris has accumulated behind the extractors if you haven’t cleaned them in a long time. 

Furthermore, dust and debris might collect inside the extractors gearbox. Spinning gears inside the gearbox transfer power from the engine to the extractors, which causes it to spin. The gears cannot turn properly if hair and filth build up inside the gearbox, causing the side brush to cease operating.

A Faulty Or Inadequately Lubricated Extractors Motor

A weak motor is another reason a Roomba extractor does not spin smoothly. There have been a few complaints of the extractors motor failing, albeit it is not particularly common. Thankfully, if you contact iRobot and explain the extractor’s behavior, they will send you a warranty replacement.

Defective Components

If the parts are damaged, the extractors may not perform as well. Run the demo on your Roomba to make sure the extractor’s motor is turning at the correct time. If the motor does not turn on, the module may have failed (although it could also be a problem in the electronics connected).

If the engine is running, but the extractor is not spinning, look for cracks or severe tearing in the yellow area of the extractor. On occasion, we’ve discovered a small crack in the yellow area of the extractor, which prevents it from spinning freely. If this is the case, renewing it with a new extractor is better.

How To Repair A Non-Spinning Roomba extractors

If you want to fix a Roomba extractor quickly and easily without getting your hands dirty, simply purchase a new Roomba extractors module. If you want to save a little money and do it yourself, here’s how to fix a Roomba extractor that isn’t spinning:

Clean The Underside Of The Extractor Of Any Dust

The first step is cleaning up all the dust that has accumulated beneath the extractors. The processes for removing and replacing the Roomba extractors are identical for all models. Remove the screw with a tiny screwdriver to remove the extractors from the Roomba. Remove the extractors and its post and clean them.

See also  How Do Portable Air Conditioners Work? Explained

Reinstall the extractors and make sure they spin freely after you’ve cleared all the dust. If everything appears to be in order, you’re good to go. If the extractors module does not turn after this, it should be fixed or replaced. Inspection of the gearbox is required to fix the extractors. 

Remove Any Dirt From The Gearbox

Remove the back cover to gain access to the extractor gearbox. Remove all the screws securing the back cover after unscrewing the extractors. When you remove the back cover, you’ll see that the extractor module is held in place by two screws. Remove the screws and lift the module.

When you have the gearbox, look for a screw that holds the cover. Remove the lid by unscrewing it. When you open the cover, the gears inside are visible. Remove each piece of equipment one at a time, then sweep out any dust or hair you find. The accumulation of gunk is what keeps the gears from spinning smoothly.

You can lubricate the gears once you’ve removed all the hair and dust you can locate. This will ensure that it continues to spin smoothly. 

Lubricate The Extractors Motor  

While you have access to the extractor motor, lightly oil it to ensure it continues to spin smoothly. Apply a modest amount of oil to the motor shaft’s small area. Surprisingly, this simple motion caused the extractors to turn better, possibly better than they had ever turned before! Keep in mind that a little grease goes a long way.

It’s time to put everything back together after cleaning and lubricating the complete extractor gearbox. Attach the extractors and turn them in by hand before reassembling the extractor module into the unit.  

How To Dismantle And Clean My Roomba Side Brush

A single screw in the middle holds the side brush in place on the robot’s underbelly. You may remove it with a normal Phillips screwdriver. Grab the brush and drag it out of the robot’s chassis after the screw has been released.

See also  Does Home Depot Cut Wood For You? Find Out!

Remove any dirt, debris, or hair accumulated on the spokes. Check the cavity where the brush is seated as well. It’s possible that dust particles have gotten into the cavity and plugged it, preventing the brush from rotating correctly. Replace the brush in its mounting position and tighten the retention screw when everything has been cleaned.

Is The Extractor Still Not Spinning?

Check the cables and connector if the extractors are still not operating after following the steps above. It could be loose, damaged, corroded, or all three at the same time. If this is the case, purchasing a new extractors module is your best option.

Purchasing a replacement extractor module is a low-cost way to extend the life of your Roomba, especially if it is older. It’s also a quick and painless way to fix a non-spinning Roomba extractor without disassembling it or getting your hands dirty.

Is The Extractor On The Roomba Supposed To Spin All The Time?

The extractors of a Roomba are supposed to spin all the time as it goes on a cleaning run.

The extractors are two on a Roomba one collects dust and deposits it on the Roomba’s route. The other accelerates it into the vacuum’s suction channel.

When Should My Roomba Extractors Be Replaced?

The high-efficiency filter and side brush on your iRobot Roomba robot should be changed every two to three months, and the debris roller (debris extractor) should be changed every three to six months to make sure it works well.

What Is The Purpose Of The Roomba Extractors?

The Roomba’s edge-sweeping extractors collect dirt, dust, and debris along the edges. It collects dirt as it rotates and deposits it in front of the Roomba’s suction channel and path. The Roomba would have overlooked the dust and dirt that builds along the perimeter of your house if it didn’t have the extractors.

What Can I Do If The Extractors On My Roomba Aren’t Spinning? 

If the extractors on your Roomba are not spinning, try cleaning, lubricating, or replacing them. Unfortunately, smart vacuums will require maintenance regularly.

What’s The Best Way To Fix My Roomba Extractors? 

If the extractors on your Roomba are physically broken, you’ll need to replace them. Fortunately, certain Roomba machines come with an extra brush, or you may get one from the company. 

Conclusion On Roomba Extractors Not Spinning 

Keep in mind that hair or dirt is the most common cause of the Roomba extractors not rotating. As a result, regular robot vacuum maintenance is required.

Check for debris wrapped around the wheels and extractors regularly. You should clean the extra and head module at least once weekly if you have a cleaning tool. If you notice any damage to the Roomba extractors, please replace them as soon as possible to maintain the device’s efficiency.

Regarding cleaning machines, general technical advancement is excellent, but we can avoid damage. The best thing we can do is keep them under control with routine maintenance.